Ice adhesion of PDMS surfaces with balanced elastic and water-repellent properties.

HYPOTHESIS: Ice adhesion to rigid materials is reduced with low energy surfaces of high receding contact angles. However, their adhesion strength values are above the threshold value to be considered as icephobic materials. Surface deformability is a promising route to further reduce ice adhesion. EXPERIMENTS: In this work, we prepared elastomer surfaces with a wide range of elastic moduli and hydrophobicity degree and we measured their ice adhesion strength. Moreover, we also explored the deicing performance of oil-infused elastomeric surfaces. The ice adhesion was characterized by two detachment modes: tensile and shear. FINDINGS: The variety of elastomeric surfaces allowed us to simultaneously analyze the ice adhesion dependence with deformability and contact angle hysteresis. We found that the impact of these properties depends on the detachment mode, being deformability more important in shear mode and hydrophobicity more relevant in tensile mode. In addition, oil infusion further reduces ice adhesion due to the interfacial slippage. From an optimal balance between deformability and hydrophobicity, we were able to identify surfaces with super-low ice adhesion.

Wetting transitions on rough surfaces revealed with captive bubble experiments. The role of surface energy.

HYPOTHESIS: Wettability of solid surfaces is mostly probed with sessile drops rather than bubbles because this method is readily followed out. This recurrent use may lead to a misleading connection of certain phenomena to the hydrophobicity/hydrophilicity of materials. For instance, the Cassie-Baxter regime and the wicking effect are generally associated only to hydrophobic and hydrophilic surfaces, respectively. However, the same phenomenology should be observed when air bubbles (underwater conditions) in contact with solid surfaces are used instead. In particular, one might expect that rough-hydrophilic surfaces become superaerophobic due to the appearance of a hybrid dewetting regime, like the Cassie-Baxter regime described for rough-hydrophobic surfaces. Otherwise, rough-hydrophobic surfaces might become superaerophilic due to air-wicking. EXPERIMENTS: To elucidate this issue, in this work, we analyzed the wettability of surfaces with very different intrinsic contact angle and roughness degree. The analysis was performed with both Sessile Drop and Captive Bubble methods. FINDINGS: Our results with captive bubbles for rough-hydrophilic surfaces revealed phenomena only explained by the occurrence of a transition from the Wenzel regime to an "inverse" Cassie-Baxter regime. In addition, our results with captive bubbles for rough-hydrophobic surfaces showed evidences of air percolation through the interconnected asperities. This effect reminds the wicking effect reproduced on rough-hydrophilic surfaces, responsible for superhydrophilicity.

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications.

Several ways to produce superhydrophobic metal surfaces are presented in this work. Aluminum was chosen as the metal substrate due to its wide use in industry. The wettability of the produced surface was analyzed by bouncing drop experiments and the topography was analyzed by confocal microscopy. In addition, we show various methodologies to measure its durability and anti-icing properties. Superhydrophobic surfaces hold a special texture that must be preserved to keep their water-repellency. To fabricate durable surfaces, we followed two strategies to incorporate a resistant texture. The first strategy is a direct incorporation of roughness to the metal substrate by acid etching. After this surface texturization, the surface energy was decreased by silanization or fluoropolymer deposition. The second strategy is the growth of a ceria layer (after surface texturization) that should enhance the surface hardness and corrosion resistance. The surface energy was decreased with a stearic acid film. The durability of the superhydrophobic surfaces was examined by a particle impact test, mechanical wear by lateral abrasion, and UV-ozone resistance. The anti-icing properties were explored by studying the ability to repeal subcooled water, freezing delay, and ice adhesion.

Testing the performance of superhydrophobic aluminum surfaces.

The analysis of wetting properties of superhydrophobic surfaces may be a difficult task due to the restless behavior of drops on this type of surfaces and the limitations of goniometry for high contact angles. A method to validate the performance of superhydrophobic surfaces, rather than standard goniometry, is required. In this work, we used bouncing drop dynamics as a useful tool to predict the water repellency of different superhydrophobic surfaces. From bouncing drop experiments conducted over a wide range of superhydrophobic surfaces, we found that those surfaces with a proper roughness degree and homogeneous chemical composition showed higher water-repellency. We also conducted a drop condensation study at saturating conditions aimed to determine whether there is direct correlation between water repellency and condensation delay. We found that the drop condensation process is strongly related to the surface topography, as well as the intrinsic wettability. The condensation is promoted on rough surfaces but it is delayed on intrinsically hydrophobic surfaces. However, the differences found in condensation delay between the superhydrophobic surfaces explored in this study cannot be justified by their chemical homogeneity nor their efficiency as water repellent surfaces, separately.

Forces between different latex particles in aqueous electrolyte solutions measured with the colloidal probe technique.

In this article, a compilation of results on direct force measurements between colloidal particles in monovalent salts carried out with the colloidal probe technique based on Atomic Force Microscopy was presented. The interaction forces between similar and dissimilar particles was studied and it was concluded that, in general, these force profiles may be satisfactorily quantified by the DLVO theory down to distances of few nanometers. However, in the specific case where the charge of one of the involved particle is close to neutral, it was found that the surface potential of this particle may change its sign depending on the sign of charge of the opposite particle. In this respect, the assumption that the surface potential of a particle is a property only related to the particle surface features and the bulk properties is called into question. Microsc. Res. Tech. 80:144-152, 2017. © 2016 Wiley Periodicals, Inc.

Specific Ion Effects and pH Dependence on the Interaction Forces between Polystyrene Particles.

Colloidal interactions have been extensively studied due to the wide number of applications where colloids are present. In general, the electric double layer force and the van der Waals interaction dominate the net force acting between two colloids at large separation distances. However, it is well accepted that some other phenomena, especially those acting at short separation distances, might be relevant and induce substantial changes in the force profiles. Within these phenomena, those related to the surface contact angle, the hydration degree of the ions, or the pH, may dominate the force profiles features, not only at short distances. In this paper, we analyzed the effect of the pH and counterion type on the long-range as well as short-range forces between polystyrene colloidal particles by using the colloidal probe technique based on AFM. Our results confirm that the features of the force profiles between polystyrene surfaces are strongly affected by the pH and hydration degree of the counterions in solution. Additionally, we performed a study of the role of the pH on the wettability properties of hydrated and nonhydrated polystyrene sheets to scan the wettability properties of this material with pH. Contact angle measurements confirmed that the polystyrene surface is hydrophobic in aqueous solutions over the entire range of pHs investigated. These results are in good agreement with the features observed in the force profiles at low pH. At high pH, a short-range repulsion similar to the one observed for hydrophilic materials is observed. This repulsion scales with the pH, and it also depends on the hydration degree of the ions in solution. This way, the short-range forces between polystyrene surfaces may be tunable with the pH, and its origin does not seem to be related to the hydrophobicity of the material.

Interaction Forces and Aggregation Rates of Colloidal Latex Particles in the Presence of Monovalent Counterions.

Force profiles and aggregation rates involving positively and negatively charged polystyrene latex particles are investigated in monovalent electrolyte solutions, whereby the counterions are varied within the Hofmeister series. The force measurements are carried out with the colloidal probe technique, which is based on the atomic force microscope (AFM), while the aggregation rates are measured with time-resolved multiangle light scattering. The interaction force profiles cannot be described by classical DLVO theory, but an additional attractive short-ranged force must be included. An exponential force profile with a decay length of about 0.5 nm is consistent with the measured forces. Furthermore, the Hamaker constants extracted from the measured force profiles are substantially smaller than the theoretical values calculated from dielectric spectra. The small surface roughness of the latex particles (below 1 nm) is probably responsible for this deviation. Based on the measured force profiles, the aggregation rates can be predicted without adjustable parameters. The measured absolute aggregation rates in the fast regime are somewhat lower than the calculated ones. The critical coagulation concentration (CCC) agrees well with the experiment, including the respective shifts of the CCC within the Hofmeister series. These shifts are particularly pronounced for the positively charged particles. However, the consideration of the additional attractive short-ranged force is essential to quantify these shifts correctly. In the slow regime, the calculated rates are substantially smaller than the experimental ones. This disagreement is probably related to surface charge heterogeneities.

Long-ranged and soft interactions between charged colloidal particles induced by multivalent coions.

Forces between charged particles in aqueous solutions containing multivalent coions and monovalent counterions are studied by the colloidal probe technique. Here, the multivalent ions have the same charge as the particles, which must be contrasted to the frequently studied case where multivalent ions have the opposite sign as the substrate. In the present case, the forces remain repulsive and are dominated by the interactions of the double layers. The valence of the multivalent coion is found to have a profound influence on the shape of the force curve. While for monovalent coions the force profile is exponential down to separations of a few nanometers, the interaction is much softer and longer-ranged in the presence of multivalent coions. The force profiles in the presence of multivalent coions and in the mixtures of monovalent and multivalent coions can be accurately described by Poisson-Boltzmann theory. These results are accurate for different surfaces and even in the case of highly charged particles. This behavior can be explained by the fact that the force profile follows the near-field limit to much larger distances for multivalent coions than for monovalent ones. This limit corresponds to the conditions with no salt, where the coions are expelled between the two surfaces.

Electric double-layer potentials and surface regulation properties measured by colloidal-probe atomic force microscopy.

We show how the colloidal-probe technique, which is based on force measurements made with the atomic force microscope, can be used to accurately determine the charging parameters of water-solid interfaces. Besides yielding accurate values of the double-layer or diffuse-layer potential, the method also allows reliable determination of the charge regulation properties of the surfaces. The latter can be quantified with a regulation parameter, which is essential to properly describe forces between interfaces, especially in asymmetric situations when one of the interfaces is charged and the other one is close to neutral. The technique relies on a highly charged probe particle, for which the charging properties are accurately determined by interpreting the double-layer contribution of the measured force profiles in the symmetric sphere-sphere geometry with Poisson-Boltzmann (PB) theory. Once the probe particle is calibrated, this particle is used to measure the force profile between an unknown substrate in the asymmetric sphere-sphere or sphere-plane geometry. From this profile, the diffuse-layer potential and regulation parameter of the substrate can be again determined with PB theory. The technique is highly versatile, as it can be used for a wide variety of substrates, including colloidal particles and planar substrates. The technique is also applicable in salt solutions containing multivalent ions. The current drawbacks of the technique are that it can only be applied up to moderately high salt levels, typically to 10 mM, and only for relatively large particles, typically down to about 1 µm in diameter. How the technique could be extended to higher salt levels and smaller particle size is also briefly discussed.

Adenovirus expressing ß2-microglobulin recovers HLA class I expression and antitumor immunity by increasing T-cell recognition.

Optimal tumor cell surface expression of human leukocyte antigen (HLA) class I molecules is essential for the presentation of tumor-associated peptides to T-lymphocytes. However, a hallmark of many types of tumor is the loss or downregulation of HLA class I expression associated with ineffective tumor antigen presentation to T cells. Frequently, HLA loss can be caused by structural alterations in genes coding for HLA class I complex, including the light chain of the complex, ß2-microglobulin (ß2m). Its best-characterized function is to interact with HLA heavy chain and stabilize the complex leading to a formation of antigen-binding cleft recognized by T-cell receptor on CD8+ T cells. Our previous study demonstrated that alterations in the ß2m gene are frequently associated with cancer immune escape leading to metastatic progression and resistance to immunotherapy. These types of defects require genetic transfer strategies to recover normal expression of HLA genes. Here we characterize a replication-deficient adenoviral vector carrying human ß2m gene, which is efficient in recovering proper tumor cell surface HLA class I expression in ß2m-negative tumor cells without compromising the antigen presentation machinery. Tumor cells transduced with ß2m induced strong activation of T cells in a peptide-specific HLA-restricted manner. Gene therapy using recombinant adenoviral vectors encoding HLA genes increases tumor antigen presentation and represents a powerful tool for modulation of tumor cell immunogenicity by restoration of missing or altered HLA genes. It should be considered as part of cancer treatment in combination with immunotherapy.

Novedades en colecho y SMSL / News in co-sleeping and SIDS

No disponible

¿Hay que hacer profilaxis de hierro en lactantes? / Do we have to give prophylactic iron supplementation to infants?

No disponible

Interaction forces, heteroaggregation, and deposition involving charged colloidal particles.

Force profiles as well as aggregation and deposition rates are studied for asymmetrically charged particles and surfaces in aqueous electrolytes theoretically. Interactions are calculated within the Derjaguin, Landau, Verwey, and Overbeek (DLVO) theory, whereby the electrostatic part is modeled at Poisson-Boltzmann (PB) level. Unequally charged surfaces are examined, from the symmetric system, where both surfaces are equally charged, to fully asymmetric systems, where the surfaces are oppositely charged. Charged-neutral systems, where one surface is charged and the other is neutral, emerge as an essential scenario. In this case, the choice of boundary conditions used for solving the PB equation is crucial, whereby constant charge and constant potential boundary conditions lead to either fully repulsive or fully attractive forces. Consequently, charge regulation has a major influence on particle aggregation and deposition rates too. In the charge-neutral case, substantial shifts in the critical coagulation concentration (CCC) are observed when the regulation properties are changed. In the presence of multivalent ions, these systems behave similarly to the symmetrically charged ones. The CCC decreases with the square of the valence in weakly charged systems, while unrealistically high charge densities are needed to recover the classical Schulze-Hardy limit, which predicts a sixth power dependence on valence.

Accurate predictions of forces in the presence of multivalent ions by Poisson-Boltzmann theory.

Forces between positively and negatively charged colloidal particles across aqueous salt solutions containing multivalent ions are measured directly with the atomic force microscope (AFM). The measurements are interpreted quantitatively with Poisson-Boltzmann (PB) theory. Thereby, the surface potentials and regulation properties of the particle surfaces are extracted from symmetric measurements between the same types of particles. This information is used to predict force profiles in the asymmetric situations involving different types of particles without any adjustable parameters. These predictions turn out to be very accurate, which demonstrates that the mean-field PB theory is reliable down to distances of about 5 nm. While various reports in the literature indicate that this theory should fail due to neglect of ion correlations, such effects seem important only at higher concentrations and smaller distances.

Measurements of dispersion forces between colloidal latex particles with the atomic force microscope and comparison with Lifshitz theory.

Interaction forces between carboxylate colloidal latex particles of about 2 µm in diameter immersed in aqueous solutions of monovalent salts were measured with the colloidal probe technique, which is based on the atomic force microscope. We have systematically varied the ionic strength, the type of salt, and also the surface charge densities of the particles through changes in the solution pH. Based on these measurements, we have accurately measured the dispersion forces acting between the particles and estimated the apparent Hamaker constant to be (2.0 ± 0.5) × 10(-21) J at a separation distance of about 10 nm. This value is basically independent of the salt concentration and the type of salt. Good agreement with Lifshitz theory is found when roughness effects are taken into account. The combination of retardation and roughness effects reduces the value of the apparent Hamaker constant and its ionic strength dependence with respect to the case of ideally smooth surfaces.

Equilibrium contact angle or the most-stable contact angle?

It is well-established that the equilibrium contact angle in a thermodynamic framework is an "unattainable" contact angle. Instead, the most-stable contact angle obtained from mechanical stimuli of the system is indeed experimentally accessible. Monitoring the susceptibility of a sessile drop to a mechanical stimulus enables to identify the most stable drop configuration within the practical range of contact angle hysteresis. Two different stimuli may be used with sessile drops: mechanical vibration and tilting. The most stable drop against vibration should reveal the changeless contact angle but against the gravity force, it should reveal the highest resistance to slide down. After the corresponding mechanical stimulus, once the excited drop configuration is examined, the focus will be on the contact angle of the initial drop configuration. This methodology needs to map significantly the static drop configurations with different stable contact angles. The most-stable contact angle, together with the advancing and receding contact angles, completes the description of physically realizable configurations of a solid-liquid system. Since the most-stable contact angle is energetically significant, it may be used in the Wenzel, Cassie or Cassie-Baxter equations accordingly or for the surface energy evaluation.

Predicting aggregation rates of colloidal particles from direct force measurements.

Direct force measurements between negatively charged colloidal latex particles of a diameter of 1 µm were carried out in aqueous solutions of various inorganic monovalent and multivalent cations with the multiparticle colloidal probe technique based on the atomic force microscope (AFM). The observed force profiles were rationalized within the theory of Derjaguin, Landau, Verwey, and Overbeek (DLVO). In the presence of monovalent and divalent cations, this theory was capable to describe the force profiles correctly down to distances of a few nm. At shorter distances, however, a strong non-DLVO attraction was identified. For more highly charged cations, an additional and more long-ranged non-DLVO attractive force is observed, and it was interpreted by surface charge heterogeneities. On the basis of these force profiles, the aggregation rates, which were independently measured by light scattering, can be predicted relatively well. The main conclusion of this study is that, in the present system, direct force measurements do capture the principal interactions driving aggregation in colloidal suspensions.

Direct measurements of forces between different charged colloidal particles and their prediction by the theory of Derjaguin, Landau, Verwey, and Overbeek (DLVO).

Force measurements between three types of latex particles of diameters down to 1 µm with sulfate and carboxyl surface functionalities were carried out with the multi-particle colloidal probe technique. The experiments were performed in monovalent electrolyte up to concentrations of about 5 mM. The force profiles could be quantified with the theory of Derjaguin, Landau, Verwey, and Overbeek (DLVO) by invoking non-retarded van der Waals forces and the Poisson-Boltzmann description of double layer forces within the constant regulation approximation. The forces measured in the symmetric systems were used to extract particle and surface properties, namely, the Hamaker constant, surface potentials, and regulation parameters. The regulation parameter is found to be independent of solution composition. With these values at hand, the DLVO theory is capable to accurately predict the measured forces in the asymmetric systems down to distances of 2-3 nm without adjustable parameters. This success indicates that DLVO theory is highly reliable to quantify interaction forces in such systems. However, charge regulation effects are found to be important, and they must be considered to obtain correct description of the forces. The use of the classical constant charge or constant potential boundary conditions may lead to erroneous results. To make reliable predictions of the force profiles, the surface potentials must be extracted from direct force measurements too. For highly charged surfaces, the commonly used electrophoresis techniques are found to yield incorrect estimates of this quantity.

Attractive Forces between Charged Colloidal Particles Induced by Multivalent Ions Revealed by Confronting Aggregation and Direct Force Measurements.

Interactions involving charged particles in the presence of multivalent ions are relevant in wide-range of phenomena, including condensation of nucleic acids, cement hardening, or water treatment. Here, we study such interactions by combining direct force measurements with atomic force microscopy (AFM) and aggregation studies with time-resolved light scattering for particles originating from the same colloidal suspension for the first time. Classical DLVO theory is found to be only applicable for monovalent and divalent ions. For ions of higher valence, charge inversion and additional non-DLVO attractive forces are observed. These attractive forces can be attributed to surface charge heterogeneities, which leads to stability ratios that are calculated from direct force measurements to be higher than the experimental ones. Ion-ion correlations are equally important as they induce the charge inversion in the presence of trivalent or tetravalent ions, and they enhance the surface charge heterogeneities. Such heterogeneities therefore play an essential role in controlling interactions in particle suspensions containing multivalent ions.

Prevención y cribado de la ferropenia en lactantes / Prevention and screening of iron deficiency in infants

La ferropenia es un problema frecuente en el lactante. Distintos estudios relacionan la ferropenia con potenciales efectos sobre el neurodesarrollo, aunque aún no existe evidencia suficiente. La mayoría de organizaciones no recomiendan la suplementación universal en lactantes sanos nacidos a término, aunque hay consenso en suplementar si hay factores de riesgo. También es tema de controversia el cribado de la ferropenia en el lactante, mientras algunas organizaciones lo recomiendan solo a grupos de riesgo, otras entidades, proponen el cribado universal. El objetivo de este artículo es revisar las necesidades de hierro durante el primer año, así como las recomendaciones de los principales comités (AU)

Iron deficiency is a frequent condition during infancy. Recent studies relate it with neurodevelopment, although there are not conclusive results. Most organizations are not recommending iron supplementation in normal infants but there is consensus about supplementing if there are risk factors. There is also controversy about screening and some groups recommend screening infants at risk, and others propose general screening. The purpose of this article is to review the requirements of iron during infancy and the different current recommendations (AU)